3.5inch RPi LCD (A), 480×320
- үнэ: 82,000 төг
480x320, 3.5 inch Touch Screen TFT LCD Designed for Raspberry Pi
SKU: 9904
Part Number: 3.5inch RPi LCD (A)
Brand: Waveshare
UPC: 799632837077
Package content:
- 3.5inch RPi LCD (A) x 1
- Touch pen x 1
- RPi screws pack (2pcs) x 1
- Quick start sheet x1
Weight: 0.056 kg
Features
- – 480×320 hardware resolution
- – Resistive touch control
- – Supports any revision of Raspberry Pi (directly-pluggable)
- – Drivers provided (works with your own Raspbian/Ubuntu/Kali)
- – Supports FBCP software driver as well, allows to config software resolution and set up dual-display
- – Size perfectly fits the Pi (Raspberry Pi B+/2B/3B/3B+)
- – High quality immersion gold surface plating
- – Combined with the Raspberry Pi, allows you to:
- – Take photos by touching (up to 17 camera modes)
- – Use software keyboard (system interaction without keyboard/mouse)
Key Parameters
| LCD TYPE | TFT |
|---|---|
| LCD INTERFACE | SPI |
| TOUCH SCREEN TYPE | Resistive |
| TOUCH SCREEN CONTROLLER | XPT2046 |
| COLORS | 65536 |
| BACKLIGHT | LED |
| RESOLUTION | 320*480 (Pixel) |
| ASPECT RATIO | 8:5 |
| POWER CONSUMPTION | TBD |
| BACKLIGHT CURRENT | TBD |
| OPERATING TEMP. (℃) | TBD |
Interface
| PIN NO. | SYMBOL | DESCRIPTION |
|---|---|---|
| 1, 17 | 3.3V | Power positive (3.3V power input) |
| 2, 4 | 5V | Power positive (5V power input) |
| 3, 5, 7, 8, 10, 12, 13, 15, 16 | NC | NC |
| 6, 9, 14, 20, 25 | GND | Ground |
| 11 | TP_IRQ | Touch Panel interrupt, low level while the Touch Panel detects touching |
| 18 | LCD_RS | Instruction/Data Register selection |
| 19 | LCD_SI / TP_SI | SPI data input of LCD/Touch Panel |
| 21 | TP_SO | SPI data output of Touch Panel |
| 22 | RST | Reset |
| 23 | LCD_SCK / TP_SCK | SPI clock of LCD/Touch Panel |
| 24 | LCD_CS | LCD chip selection, low active |
| 26 | TP_CS | Touch Panel chip selection, low active |
External Dimension
Development Resources
Wiki : www.waveshare.com/wiki/3.5inch_RPi_LCD_(A)
FAQ
- Why the LCD doesn’t work with my Raspbian?
- To use the LCD with the Raspberry Pi official image, driver (SPI touch interface only) should be installed first. Please refer to the user manual.
However, for the first testing, you may want to use our image directly (if provided). - Why the LCD still doesn’t work with the Waveshare provided image?
- Make sure the hardware connection is correct and connects fine.
Make sure the image in TF card is burnt correctly.
The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact. - Which power supply should I use?
- It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC’s USB port might have not enough power.
For large size LCDs, say, 10inch diagonal or more, another stand-alone power adapter is also required to provide power to the LCD.
For more info, please check the wiki page.
Anti-Piracy
CAUTION: This product is protected by patent, anyone making copies/knock-offs SHOULD be held liable pursuant to law.
Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They’re usually some poor copies of our early hardware revisions, and comes with none support service.
To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing:
